-- Copyright (C) 1991-2013 Altera Corporation -- Your use of Altera Corporation's design tools, logic functions -- and other software and tools, and its AMPP partner logic -- functions, and any output files from any of the foregoing -- (including device programming or simulation files), and any -- associated documentation or information are expressly subject -- to the terms and conditions of the Altera Program License -- Subscription Agreement, Altera MegaCore Function License -- Agreement, or other applicable license agreement, including, -- without limitation, that your use is for the sole purpose of -- programming logic devices manufactured by Altera and sold by -- Altera or its authorized distributors. Please refer to the -- applicable agreement for further details. -- -- This is a Quartus II output file. It is for reporting purposes only, and is -- not intended for use as a Quartus II input file. This file cannot be used -- to make Quartus II pin assignments - for instructions on how to make pin -- assignments, please see Quartus II help. --------------------------------------------------------------------------------- --------------------------------------------------------------------------------- -- NC : No Connect. This pin has no internal connection to the device. -- DNU : Do Not Use. This pin MUST NOT be connected. -- VCC : Dedicated power pin, which MUST be connected to VCC. -- VCCIO : Dedicated power pin, which MUST be connected to VCC -- of its bank. -- GND : Dedicated ground pin. Dedicated GND pins MUST be connected to GND. -- It can also be used to report unused dedicated pins. The connection -- on the board for unused dedicated pins depends on whether this will -- be used in a future design. One example is device migration. When -- using device migration, refer to the device pin-tables. If it is a -- GND pin in the pin table or if it will not be used in a future design -- for another purpose the it MUST be connected to GND. If it is an unused -- dedicated pin, then it can be connected to a valid signal on the board -- (low, high, or toggling) if that signal is required for a different -- revision of the design. -- GND+ : Unused input pin. It can also be used to report unused dual-purpose pins. -- This pin should be connected to GND. It may also be connected to a -- valid signal on the board (low, high, or toggling) if that signal -- is required for a different revision of the design. -- GND* : Unused I/O pin. Connect each pin marked GND* directly to GND -- or leave it unconnected. -- RESERVED : Unused I/O pin, which MUST be left unconnected. -- RESERVED_INPUT : Pin is tri-stated and should be connected to the board. -- RESERVED_INPUT_WITH_WEAK_PULLUP : Pin is tri-stated with internal weak pull-up resistor. -- RESERVED_INPUT_WITH_BUS_HOLD : Pin is tri-stated with bus-hold circuitry. -- RESERVED_OUTPUT_DRIVEN_HIGH : Pin is output driven high. -- NON_MIGRATABLE: This pin cannot be migrated. --------------------------------------------------------------------------------- --------------------------------------------------------------------------------- -- Pin directions (input, output or bidir) are based on device operating in user mode. --------------------------------------------------------------------------------- Quartus II 64-Bit Version 13.0.1 Build 232 06/12/2013 Service Pack 1 SJ Web Edition CHIP "e2" ASSIGNED TO AN: EPM7032SLC44-10 Pin Name/Usage : Location : Dir. : I/O Standard : Voltage : I/O Bank : User Assignment ------------------------------------------------------------------------------------------------------------- init_l : 1 : input : TTL : : : N GND+ : 2 : : : : : VCC : 3 : power : : : : iob5_l : 4 : output : TTL : : : N iob6_l : 5 : output : TTL : : : N iob7_l : 6 : output : TTL : : : N TDI : 7 : input : TTL : : : N iob8_l : 8 : output : TTL : : : N iob10_l : 9 : output : TTL : : : N GND : 10 : gnd : : : : RESERVED : 11 : : : : : RESERVED : 12 : : : : : TMS : 13 : input : TTL : : : N RESERVED : 14 : : : : : VCC : 15 : power : : : : biop1 : 16 : input : TTL : : : N RESERVED : 17 : : : : : RESERVED : 18 : : : : : tx_sel : 19 : input : TTL : : : N rx_data : 20 : input : TTL : : : N rx_sel : 21 : input : TTL : : : N GND : 22 : gnd : : : : VCC : 23 : power : : : : biop4 : 24 : input : TTL : : : N biop2 : 25 : input : TTL : : : N RESERVED : 26 : : : : : RESERVED : 27 : : : : : RESERVED : 28 : : : : : RESERVED : 29 : : : : : GND : 30 : gnd : : : : iob11_l : 31 : output : TTL : : : N TCK : 32 : input : TTL : : : N iob4_l : 33 : output : TTL : : : N irq_l : 34 : output : TTL : : : N VCC : 35 : power : : : : dsrttl : 36 : output : TTL : : : N txdttl : 37 : output : TTL : : : N TDO : 38 : output : TTL : : : N iob9_l : 39 : output : TTL : : : N skip_l : 40 : output : TTL : : : N acclr_l : 41 : output : TTL : : : N GND : 42 : gnd : : : : rx_rate : 43 : input : TTL : : : N GND+ : 44 : : : : :