;+
;
; RL11/RL01,RL02 boot device driver.
;
; By John Wilson.  This file is hereby released into the public domain.
;
; 11/16/95	JMBW	Created.
;
;-
rlcs=	0		;(774400) control/status
rlba=	2		;(774402) bus addr
rlda=	4		;(774404) disk addr
rlmp=	6		;(774406) multipurpose
;
rlrtry=	5		;max retry count
;
rlerr=	100000		;composite error
;
rlrdy=	200		;ready
;
rlgst=	2*2		;get status
rlsek=	3*2		;seek
rlrdh=	4*2		;read header
rlrdd=	6*2		;read data
;
rldry=	1		;drive ready
;
	.btini	<DL>		;RL11 init code
	mov	bcsr,r0		;get base CSR
	movb	1(r0),r1	;get unit #
	bic	#^C3,r1		;isolate
	mov	r1,bunit	;save
	call	getpos		;update RLPOS
	.btfin			;finish up boot process
;+
;
; RL11/RL01,RL02 bootstrap read driver.
;
; r5	memory addr
; r4	block count
; r3	starting block
;
;-
read:	mov	#rlrtry,(pc)+	;init retry count
retry:	 .blkw			;retry count
10$:	; compute starting sector addr
	mov	r3,r1		;copy block #
	mov	#-64.,r0	;init track to 0
20$:	add	#64.,r0		;count the track
	sub	#20.,r1		;bite off a track
	bcc	20$		;loop until we get there
	add	#20.,r1		;undo last SUB
	; r0=track, r1=sector -- seek if needed
	cmp	r0,rlpos	;same as curr head posn?
	beq	50$		;yes
	mov	rlpos,r2	;get old posn
	mov	r0,rlpos	;save new posn
	mov	r3,-(sp)	;save
	mov	r0,r3		;copy
	ror	r0		;move HS into bit 4
	ror	r0
	bic	#^C20,r0	;isolate
	bic	#100,r2		;remove HS bits
	bic	#100,r3
	sub	r3,r2		;assume moving heads out
	bcc	30$		;right
	neg	r2		;wrong, take abs val (overflow works out OK)
	bis	#4,r0		;set DIR bit
30$:	bis	r2,r0		;get cylinder delta
	inc	r0		;bits <1:0>=01 for "seek" cmd
	mov	bcsr,r2		;get CSR
	mov	r0,rlda(r2)	;write cyl/head to disk addr register
	mov	bunit,r3	;get unit
	swab	r3		;in high half
	bis	#rlsek,r3	;cmd=SEEK
	mov	r3,(r2)		;send cmd
	mov	(sp)+,r3	;restore
40$:	mov	(r2),r0		;poll CSR
	bmi	80$		;error
	bic	#^C<rlrdy!rldry>,r0 ;isolate control ready and drive ready
	cmp	r0,#rlrdy!rldry	;both set?
	bne	40$		;wait until so
50$:	; drive is on-track, get on with the read, r1=starting sector #
	; RL01/02 can't do spiral reads so we can only go till end of track
	mov	#20.,r0		;# blocks per track
	sub	r1,r0		;find # left on track
	cmp	r0,r4		;do we have at least that many to do?
	blo	60$
	 mov	r4,r0		;no, stop early
60$:	mov	bcsr,r2		;point at CSR
	add	#rlmp,r2	;point at MP reg
	swab	r0		;convert blk count to WC
	neg	r0		;negative WC
	mov	r0,(r2)		;write to multipurpose reg
	asl	r1		;convert blk # to starting sec # (0-39.)
	bis	rlpos,r1	;get cyl/head bits too
	mov	r1,-(r2)	;write to disk addr reg
	mov	r5,-(r2)	;write bus addr reg
	mov	bunit,r1	;get unit
	swab	r1		;in LH
	bis	#rlrdd,r1	;cmd=read data
	mov	r1,-(r2)	;write to CSR
70$:	bit	#rlerr!rlrdy,(r2) ;poll
	bmi	80$		;error
	beq	70$
	; success, prepare for next track
	neg	r0		;absolute WC
	add	r0,r5		;update BA
	add	r0,r5
	swab	r0		;convert WC to block count
	add	r0,r3		;bump starting block
	sub	r0,r4		;subtract from total
	bne	read
	rti
80$:	; error
	call	getpos		;clear errors, double-check position
	dec	retry		;time to give up?
	bne	10$		;no
	bpt			;yes
;+
;
; Clear errors, read a disk header to find out our cyl/head location.
;
; r3-r5	preserved
;
;-
getpos:	mov	#rlrtry,r2	;init counter
	mov	bcsr,r1		;get CSR addr
10$:	mov	#13,rlda(r1)	;reset error bits (if set)
	mov	bunit,r0	;save
	swab	r0		;back in LH
	bis	#rlgst,r0	;get status
	mov	r0,(r1)		;send cmd
20$:	bit	#rlerr!rlrdy,(r1) ;wait until ready
	bmi	40$
	beq	20$
	add	#rlrdh-rlgst,r0	;change cmd to "read header"
	mov	r0,(r1)		;send cmd
30$:	bit	#rlerr!rlrdy,(r1) ;wait until ready
	beq	30$
	bpl	50$
40$:	dec	r2		;give up yet?
	bne	10$		;no
	bpt			;failed
50$:	mov	rlmp(r1),r0	;fetch header word
	bic	#77,r0		;remove sector
	mov	r0,(pc)+	;save
rlpos:	 .blkw			;current cyl/head
	cmp	rlmp(r1),rlmp(r1) ;flush out FIFO (is this needed?)
	rts	pc
;
	.end	boot