To Do

8L=20: Debug W076X and M452X.=20; Upgrade console with W076X and M452X.=20; Determine why core is erased sometimes, and FOCAL won=92t = run.=20; Connect the DF32 emulator and get it working.=20; Install 4K Disk system on DF32 emulation.=20
8i=20: Check out power supply.=20; Reconnect power, fix front panel control logic.=20; Fix M706, console subsystem, get it working.=20; Upgrade console with W076X and M452X.=20; Get PC04 working with it, or another DF32 emulator.=20
TTY#1=20: Try to get it working. Keyboard is messed up, reader is = dead.=20
TTY#2=20: Repair printer and punch. They worked recently!=20; Figure out how to add reader-run.=20
TTY#3=20: Fix printer and punch.=20; Figure out the wiring harness.=20
RK05#1=20: Install the new elbow when it comes.=20; Clean up the inside of the drive.=20; Rack mount the drive.=20
RK05#2=20: Clean up the inside of the drive.=20; Rack mount the drive in the bottom of the rack, on pivot = rails.=20
8e#1=20: Fix or replace low 8k core memory.=20; Fix or replace RK8E. (Skip if ready shouldn=92t load AC).=20; Make or buy cable for RK8E. Get RK05s working with it.=20; Fix or replace the EAE. (Mode B isn=92t working.)=20
8e#2=20: Test for basic operation. Decide which 8e to keep in the = rack.=20; Replace semiconductor memory.=20; Try to fit into one back-plane.=20; Get TU56, TU10, DSD410, PC04 to work.=20
TU56=20: Replace leaky electrolytic and debug power supply.=20; Connect to TD8E and see if it works.=20
TU10=20: Debug power supply.=20; Make or buy cable for it.=20; Connect to 8e and see if it works.=20
PC04=20: Debug power supply.=20; Connect to PC8E and see if it works.=20
DSD410=20: Connect to 8e and see if it works.=20
8eExt=20: Determine if additional back-plane is needed. Sell if not.=20
DSD411=20: Determine if it works.=20; Add it to the 8e, if so.=20
8a#1=20: Get the front panel working. Verify CPU operation.=20; Get the RX02s working with it.=20; Get the RL02s working with it.=20
RX02s=20: Debug why DD doesn=92t work well.=20; Get them working with the 8a, instead of the 8e.=20
RL02s=20: Get them rack mounted, rather than just stacked in the rack. =; Get them working with the 8a.=20
8a#2=20: Assemble, test, debug, sell.=20
DMII=20: Get it to boot from floppy.=20; Try to find hard disk or RX02 card for it.=20
DMIII=20: Working! Try to find a place for keyboard/display.=20
Tty43#1=20: Find a source for ribbons.=20; Get it working, or sell it.=20; Decide whether to keep it.=20
Tty43#2=20: Find a source for ribbons.=20; Fix keyboard problems.=20; Decide whether to keep it.=20
TU55=20: Get it working. Install it on the 8a with spare TD8e.=20
11/34=20: Get it working with RX01. Sell it.=20
RX01=20: Get it working with 11/34. Sell it.=20
Spares=20: Determine which work. Debug or sell the rest.=20

=
		*My PDP-8 Stuff* *To Do*



	Home \| = 03/04 = \|=20 02/04 = \|=20 01/04 = \|=20 12/03 = \|=20 11/03 = \|=20 Pictures \|=20 To Do \|=20 Bulb Page =


		Here is a list of objects in the collection and their status, = expressed=20 as a To Do list.



		8L=20 Debug W076X and M452X.=20 Upgrade console with W076X and M452X.=20 Determine why core is erased sometimes, and FOCAL won=92t = run.=20 Connect the DF32 emulator and get it working.=20 Install 4K Disk system on DF32 emulation.=20 8i=20 Check out power supply.=20 Reconnect power, fix front panel control logic.=20 Fix M706, console subsystem, get it working.=20 Upgrade console with W076X and M452X.=20 Get PC04 working with it, or another DF32 emulator.=20 TTY#1=20 Try to get it working. Keyboard is messed up, reader is = dead.=20 TTY#2=20 Repair printer and punch. They worked recently!=20 Figure out how to add reader-run.=20 TTY#3=20 Fix printer and punch.=20 Figure out the wiring harness.=20 RK05#1=20 Install the new elbow when it comes.=20 Clean up the inside of the drive.=20 Rack mount the drive.=20 RK05#2=20 Clean up the inside of the drive.=20 Rack mount the drive in the bottom of the rack, on pivot = rails.=20 8e#1=20 Fix or replace low 8k core memory.=20 Fix or replace RK8E. (Skip if ready shouldn=92t load AC).=20 Make or buy cable for RK8E. Get RK05s working with it.=20 Fix or replace the EAE. (Mode B isn=92t working.)=20 8e#2=20 Test for basic operation. Decide which 8e to keep in the = rack.=20 Replace semiconductor memory.=20 Try to fit into one back-plane.=20 Get TU56, TU10, DSD410, PC04 to work.=20 TU56=20 Replace leaky electrolytic and debug power supply.=20 Connect to TD8E and see if it works.=20 TU10=20 Debug power supply.=20 Make or buy cable for it.=20 Connect to 8e and see if it works.=20 PC04=20 Debug power supply.=20 Connect to PC8E and see if it works.=20 DSD410=20 Connect to 8e and see if it works.=20 8eExt=20 Determine if additional back-plane is needed. Sell if not.=20 DSD411=20 Determine if it works.=20 Add it to the 8e, if so.=20 8a#1=20 Get the front panel working. Verify CPU operation.=20 Get the RX02s working with it.=20 Get the RL02s working with it.=20 RX02s=20 Debug why DD doesn=92t work well.=20 Get them working with the 8a, instead of the 8e.=20 RL02s=20 Get them rack mounted, rather than just stacked in the rack. = Get them working with the 8a.=20 8a#2=20 Assemble, test, debug, sell.=20 DMII=20 Get it to boot from floppy.=20 Try to find hard disk or RX02 card for it.=20 DMIII=20 Working! Try to find a place for keyboard/display.=20 Tty43#1=20 Find a source for ribbons.=20 Get it working, or sell it.=20 Decide whether to keep it.=20 Tty43#2=20 Find a source for ribbons.=20 Fix keyboard problems.=20 Decide whether to keep it.=20 TU55=20 Get it working. Install it on the 8a with spare TD8e.=20 11/34=20 Get it working with RX01. Sell it.=20 RX01=20 Get it working with 11/34. Sell it.=20 Spares=20 Determine which work. Debug or sell the rest.=20



		Last=20 updated on My PDP-8 Stuff


		=0A= =0A= *My PDP-8 Stuff* =0A= =0A=



	=0A= =0A= Home \| 03/04 \| = 02/04 \| = 01/04 \| = 12/03 \| = 11/03 \| = Pictures = \| To Do \| = Bulb Page=0A= =0A= =0A=